The Globe and Mail: The most important new features and news in tech, business, health, culture, entertainment, finance, weather, politics and more

With the release of the new Android and iOS operating systems this year, it’s time to take a look at the new features.

We have a look in depth at some of the most important and most exciting new features for Android and Apple devices. Read more

How to install an engine on a ship using a piston

An article by Peter Osterberg on the New Scientist website, published today, has some important points to make.

First, it has the support of the European Commission and the United Nations Environment Programme (UNEP), who are both on board the programme to ensure that the engine is safe and can be used on any ship.

Second, it is based on an engine that is already in use on some of the world’s most important ships.

The article describes the piston system, the main components, and a few details about the installation of an engine.

The installation is easy, but also a bit tricky: the piston assembly must be installed in the water, which is not very easy to do in the case of an offshore drilling rig, but can be done on an offshore rig.

The system, called a “Piston-and-Clamp,” has to be built up in two parts, one in the hull and one at the deck.

The piston must be bolted onto the deck using a simple chain.

The two parts are then joined with a simple steel plate.

A simple steel cable is then used to attach the two parts together, allowing the two pistons to move freely through the water.

The assembly is then placed into the ship’s hold.

This can be tricky if the vessel is on a fast-moving vessel, which could easily require a crane or jack to move the piston and clamp.

To get the installation completed safely and quickly, the ship must be equipped with the proper pumps.

In this case, the pumps have to be installed by the ship owners themselves, which may require a skilled professional to do the job.

The boat engine installation is a bit more complicated.

It is based around an engine, but this is not as simple as it sounds.

The pump is mounted on the ship, and is attached to a gear.

The gear is then attached to the engine’s main shaft, which has a gearhead.

The engine’s shaft then runs through the gearhead, and the gears are driven through the shaft to move both pistons.

The watertight seal between the two components is then formed, and then the gear and shaft are connected together to attach them to the main shaft.

This works fine on an ocean vessel, but is not so good on a sailing vessel.

This is why an offshore oil rig needs a boat engine.

That’s why an off-shore drilling rig is required.

The pistons are bolted onto a deck, which also has a deck-mounted gearhead and an engine shaft.

The main shaft runs through a gear on the deck, and an attached hydraulic pump.

The hydraulic pump is attached via a chain to the piston.

The crane and jack are used to drive the pistons and clamps.

The pumping is done under water, and can even be done from a ship.

The new article has some interesting details about a different part of the installation process, but it doesn’t go into all of the details.

The part where the piston is bolted onto deck is called a gasket, which means it is bolted to the deck directly on the engine, and has a hole drilled through it to hold it in place.

This means that it can be easily removed when the ship is ready to use the engine.

There are some important details to keep in mind when building the engine itself, however.

The gasket can be bolted to an engine block, which will hold the gasket in place, but will also allow the piston to move around when the gaskets are being tightened.

To do this, the piston has to rotate through the gasses, and that will require a small amount of force.

If you are installing the gassets on a small vessel, or if you have a ship with a large number of engines, it might be more appropriate to use a crane and a jack, but the information is still there for people with less experience.

In order to use this new system, however, it needs to be attached to an offshore drill rig.

There is a good chance that you won’t be able to get that rig installed until you are on a very large vessel.

In the article, Osterberg notes that the US National Research Council (NRC) is supporting the installation with research funding, and this means that some of their research funding will go towards developing this technology.

The NRC is a consortium of universities and research institutions, which includes the National Oceanic and Atmospheric Administration (NOAA), the US Department of Energy (DOE), and the National Science Foundation (NSF).

The NERC is a federally funded agency, and therefore its funding can be spent on research and development of this technology and related systems.

Osterburg also says that the installation has been “demonstrated successfully on an existing offshore drilling platform, and could potentially be used to construct new drilling rigs.”

The drilling rig that is used in the article is a Type II diesel-electric oil rig,